How to empty a soda can, then fill it back up with something else, then close it?!
help! :]Www@FoodAQ@Com
Answers:
Take the tab and turn it to a 5 o' clock position (12 o'clock being where the top of the tab is before opening!.!.like the hands on a clock)
Start pulling the tab up!.!.!.!.!.slowly until the tab inside starts to surface!.
Once the pop tab is visible carefully pull up on the tab or use a tool to bring the tab to the surface!.
Then run your fingers around the edges of the tab to close it!.!.!.!.!.!.the pop tab will reseal and is larger then the hole!.!.!.!.it only goes down because the metal is flexible and flexed into the hole when you first opened it!.Www@FoodAQ@Com
Start pulling the tab up!.!.!.!.!.slowly until the tab inside starts to surface!.
Once the pop tab is visible carefully pull up on the tab or use a tool to bring the tab to the surface!.
Then run your fingers around the edges of the tab to close it!.!.!.!.!.!.the pop tab will reseal and is larger then the hole!.!.!.!.it only goes down because the metal is flexible and flexed into the hole when you first opened it!.Www@FoodAQ@Com
I can only imagine WHY you'd want to do that!. But since soda cans are made in and filled in a factory, you'll have a tough time doing it!.
(If you want to try, you could cut off the cop of a can without popping the top!. Empty the soda so you have 2 pieces, fill it with "whatever", and try to weld or soldier these 2 pieces together without setting the can on fire or evaporating the "liquid"!. !.!. even still, it would probably look really obvious!.)Www@FoodAQ@Com
(If you want to try, you could cut off the cop of a can without popping the top!. Empty the soda so you have 2 pieces, fill it with "whatever", and try to weld or soldier these 2 pieces together without setting the can on fire or evaporating the "liquid"!. !.!. even still, it would probably look really obvious!.)Www@FoodAQ@Com
I source from a Coke plant in my area!. If you visit the factory you will notice that the tops are sealed on, not the pull tab!. There would have to be a way to pop off the silver top part, the whole top piece of the can, without damaging anything!. Resealing would just be a matter of non toxic glue, or solder like some had mentioned!.
I definitely don't condone alcohol drinking, let alone having it be underage though!. So try to use this as a friendly prank!.Www@FoodAQ@Com
I definitely don't condone alcohol drinking, let alone having it be underage though!. So try to use this as a friendly prank!.Www@FoodAQ@Com
ExperienceWww@FoodAQ@Com
I just wrote very discriptive answer, then read your side note!. I don't really want to help you drink underage!. I originally thought you were just curious but no!. Sorry, dude, but you shouldn't try that!. I don't promote that stuff!. Do it on your own, or find someone other than me! If I were you I would wish I didn't put that side not on now!. No offense, but I am trying to help you!. Just don't sneak around, you will most likely get in bug trouble! Think!.!.!. But hey don't have to listen!Www@FoodAQ@Com
He says you're a rapist and i shouldn't help you, but being the president of the child molester's association of america, i could help you out XD except i couldn't because i'm about as slick as a pair of cleats!. that's not very slick, if you really must know!.Www@FoodAQ@Com
Are you playing a trick on someone!? I did once with a can of beer!. Poke a hole in the botton and empty the contents!. Then take a piece of papertowel (small) shove it in the hole and put a piece of tape over it!.Www@FoodAQ@Com
That must be almost impossible, you could try getting something small and thin and try and pull the little metal peice up!.!. good luck!?
or get one of your mates to sneak alcohol out of their house!.
- have a star!. :]Www@FoodAQ@Com
or get one of your mates to sneak alcohol out of their house!.
- have a star!. :]Www@FoodAQ@Com
Just buy it on your way to wherever you're going!. I know you're not going after your parents' booze!. If she checks your bottles, I can guarantee that she checks the levels in her own!.Www@FoodAQ@Com
refill it then solder something to the part that opens then pull untill it looks closed then solder it shut USE LEAD FREE SOLDER!!Www@FoodAQ@Com
i think using a thumb tack and poking a small hole in the bottom them sealing it with duct tape or something might work !.!.!.!.!.be careful dont get yourself in trouble :)Www@FoodAQ@Com
poke a hole from the bottom refill it upside doewn close it with something and then wa la
i don't know if it's gonna work though!.Www@FoodAQ@Com
i don't know if it's gonna work though!.Www@FoodAQ@Com
Drill two holes in the bottom
Pour out the liquid
Add new liquid
Put some sort of putty over the holes!. or weld it i guess!. Hot glue!?Www@FoodAQ@Com
Pour out the liquid
Add new liquid
Put some sort of putty over the holes!. or weld it i guess!. Hot glue!?Www@FoodAQ@Com
wanna tip!?! DONT DRINK!!! ITS THAT SIMPLE!!!!!!!! (but even if, i ithnk a good way to do this is very complicated welding system!.!.!.!.)Www@FoodAQ@Com
This sounds like date rape!.
Anyone who gives an answer is helping a rapist!.
DONT DO ITWww@FoodAQ@Com
Anyone who gives an answer is helping a rapist!.
DONT DO ITWww@FoodAQ@Com
you cant
unless you weld
you could try a bottleWww@FoodAQ@Com
unless you weld
you could try a bottleWww@FoodAQ@Com
i suspect your evilWww@FoodAQ@Com